Hice un SKATE con motor de MOTOSIERRA (creativo)

Hice un SKATE con motor de MOTOSIERRA (creativo)


Hello friends, welcome to a new video of the channel where we are going to do today is a kind of motorized skate a motorized longboard, here I have mine and we are going to do it with this this is one, it’s a machine from a chainsaw that the saw is missing now, that he had it there. This quite deteriorated but … it’s going to serve, it’s going to serve. It has 40cc and … and nothing I think that this will work Epa! will serve well for to motorize a longboard, I do not need much power good for to handle the well, to operate from a distance the accelerator of the chainsaw had two options which would be the most viable, or use a cable uh, like it’s the typical motorcycle accelerator or do it one more way, I do not know, for my simple because I have more experience and it was easier so, I chose to do this which is with a servomotor and with a control what would it be basically when I accelerate here, this would go in my hand would move the servo motor that, connect it to a battery, there’s the receiver and connect the “esk”, that the truth is not as it is said in Spanish, but it is the motor controller, which does not that does not have an engine, but that I connect it because I did not have the adapter current, so it’s not bad that you have it does not influence anything the idea would be that this servomotor go here I think the best way to put it would be So, because it fits, really, very well Y I do not know if it looks that would pull me, the cable, the accelerator that would be put here, I have here a piece of wire, which I’m going to hook there and the other end to the servomotor so if it’s just when I activate that would pull and accelerate the machine … good day two, I just found a slight problem with the with the machine, which is that, the motor rotates to the opposite side to which we want it to turn, then of course, if we put it let’s turn on the longboard and let’s go back, then we also do not have the possibility to put the chain around, because here is the naphtha tank and we could not cut it, because was going to escape everything, the solution we came up with was to put The most out clutch from … right at the tip of the shaft and put the bell from the outside and here weld the pinion and FAIL! and we weld it in the crown to be able to pull the chain back, without touching the naphtha tank this should go here would be a little more out of the skate structure so we are going to have to cross a couple of intermediate irons so that it is well caught the original skate wheels, the back wheels we’re going to take out so let’s do that now I’m staying, it’s pretty good we just screwed it, the engine is missing the engine would go in this part, but let’s see if one of the most important things, right? if this really supports us I’m as if Dad knew Hey! I’m pretty good, I think it’s going to be able to bend quite well because, it turns … this terrific man! Look, it looks like a motorcycle Tron chavón I love it, let’s try to put it on the engine goes here and this space would remain It hurts, it broke! the clutch broke What’s up friends? day four, I already believe in the project what we are going to do now, is change this old chainsaw, for this other that this is a bigger cylinder and a bigger power but I do not change it for that, if not because This chainsaw has many carburetor problems and besides that I do not get the new clutch so let’s put it let’s put the other one to see what wave and so the pinion would already be put and the bell what would remain would now be to adapt this nut, this washer, I say, here so that nothing moves directly and everything is fine What happened? This is the end of … -It broke this is the end of skate man, it’s just broken everything the best thing to do this was to buy a ruleman holder and grab it here but we did it with, half with teeth and nothing, it lasted a bit and then it broke so it worked! that’s what we wanted

100 Replies to “Hice un SKATE con motor de MOTOSIERRA (creativo)”

  1. La idea está buena. El que lo hayas hecho funcionar un par de metros ya es un logro!
    Te recomiendo lo tocar el embrague.usa correa dentada y usa sus respectivas poleas. Recorda que la corona trasera puede llegar casi al tamaño de la rueda mientras que la corona del embrague tiene que ser lo más chica posible mientras tanto encastre la polea.con ese tipo de relación pasas vueltas a fuerza. Y te recomiendo usar mando con cable de acelerador y freno. Se suele poner el disco de freno del lado izquierdo atornillado bien centrado en la llanta trasera.usa bujes para no dejar espacios de extremo a extremo de eje.en lo posible hace una base de caño de punta a punta recorda que le vibración hace desastres y necesitas agarrar el motor en una base firme que no ceda.seguramente ya te habrás dado cuenta pero va el dato igual! Las ruedas de adelante tienen que ser más grandes y de goma por que vas a andar como un campeón asta que un posito o marca en el suelo te va a mandar a volar además esas ruedas apenas soportan el peso y tracción de una persona .se parten y a la mierda! Te paso los datos por que por el 97" ya hice algo parecido con un amigo y lo dejamos por que no era viable más por las ruedas delanteras y por que no existian los frenos a disco. Buen proyecto.👍🏻

  2. A esa motosierra no se le despegaba el embrague, me doy cuenta porque hice un triciclo de drift y hasta que el embrague pegaba se soltaba como le digan así el mismo ruido

  3. Buen video chee, pero podrias haber puesto la motosierra sobre la rueda asi no perdes espacio y tener mas estabilidad. Saludos

  4. Yo también vine por la publicidad de instagram jajaja me cague de risa, que bueno ver este tipo de videos made in argentina, me suscribo

  5. Pendeja hay una empresa no me acuerdo como se llama que hace motores para esas patinetas búscala sale mas barato noce

  6. con el motor de motocierra podrias hacer uno moto del tipo cros amigo ME SERVIRIA MUCHO XQ YO QUIERO HACER UNA Y NO ME SALE LA IDEA

  7. Amigo una pregunta k motor puedo usar para la construcción de una jet boat k me recomiendas tu un motor de moto cierra o un motor de cortar pasto de más de mano espero tu respuesta pronto

  8. Me gustan tus proyectos tienes la misma manera de pensar que yo sigue asi me gusta por wur eses los proyectos en un solo videl din degunta parte

Leave a Reply

Your email address will not be published. Required fields are marked *